Jet-tools JJ-8CS Manuale Utente

OWNER’S MANUALJJ-8CS Woodworking JointerJET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000A WMH Company Auburn, WA 98071-1349 Fax: 1-800

1045° Fence AdjustmentNote: Whenever making an adjustment to the fence,lift the fence up slightly after releasing the lockhandle to avoid scratching t

115. When the outfeed table and blade number oneare the same height, tighten table lock screw.6. The knives must be parallel with the outfeedtable. B

12Installing V-Belts1. Disconnect the machine from the powersource, unplug.2. Remove the lock knob (A, Fig. 14) and belt guard(B, Fig. 14).3. Place v-

13Installing Access Cover1. Install access cover by placing bottom of panelinto access in stand and fastening by turninglatch (Fig. 17).If the access

14Operation WARNINGKeep all guards in place and in adjustmentat all times during the cutting procedure!Keep hands away from the cutterhead! Donot p

15Jointing Warped MaterialIf the work to be jointed is cupped or warped, takelight, repetitive cuts until the surface is flat. Forc-ing the material

16Rabbet Cut WARNINGRabbeting requires the removal of thecutterhead guard. Use extreme cautionwhen making rabbeting cuts and replacethe guard immed

176. Insert lock bar and screws and tighten to holdin place. Blades are set at the proper heightwhen the top of the blade is 1/16" above thecutt

18Sharpening the Knives WARNINGBlades are extremely sharp! Use cautionwhen handling. Failure to comply maycause serious injury!1. Disconnect the m

19Trouble-shootingelbuorTesuaCelbissoPnoituloSehtnodevacnocsikcotsdehsiniF.dnedeeftuoehtnahtrehgihsipitefinK.elbatlevelsitioselbatdeeftuoesiaR.pitefin

2Warranty & ServiceThe JET Group warrants every product it sells. If one of our tools needs service or repair, one of our AuthorizedRepair Statio

20Fence Assembly

21Parts List for the JJ-8CS Woodworking JointerFence AssemblyIndex PartNo. No. Description Size Qty.1 ... JC-F01...

22Bed Assembly

23Bed AssemblyIndex PartNo. No. Description Size Qty.1 ... JC-T01...Base ...

24Stand and Motor Assembly

25Stand and Motor AssemblyIndex PartNo. No. Description Size Qty.1 ... JC-M01W ...Stand...

26Cutterhead Assembly

27Cutterhead AssemblyIndex PartNo. No. Description Size Qty.1 ... JC-C01 ...Cutterhead...

28Wiring Diagram

3WARNINGWear eye protection.Always keep cutterhead and drive guards in place and in proper operating condition. Do notremove guard for rabbeting op

4• Don’t overreach. Keep proper footing and balance at all times.• Maintain tools with care. Keep tools sharp and clean for best and safest performa

5Table of ContentsWarranty...

6Levers and Controls1. Handwheel for Outfeed Table 8. On/Off Switch2. Outfeed Table 9. Rabbeting Ledge3. Fence 10. Table Lock Knob4. Fence Adjustment

7Contents of Shipping CartonsNote: unit shipped in two cartons.Stand Carton1. Stand with Motor1. Stand Door1. Dust Chute w/ Mounting HardwareMain Unit

8Installing Bed to Stand1. Use an assistant or hoist mechanism to placebed assembly on top of stand. Be sure identi-fication label on the bed faces t

9Assembling Knife-Setting Gauge1. Place the two bases (A, Fig. 4) onto each endof the bar (B, Fig. 4). Snap the four E-rings (C,Fig. 4) into the groo